15 Inch Lcd Display 1024x768 Full Viewing Angle Lvds Interface 20 Pins

General Description:

DV150X0M-N10 is a color active matrix TFT LCD MDL using amorphous silicon TFT's (Thin Film Transistors) as an active switching devices. This MDL has a 15 inch diagonally measured active area with XGA resolutions (1024 horizontal by 768 vertical pixel array). Each pixel is divided into RED, GREEN, BLUE dots which are arranged in vertical stripe and this module can display 16.7M colors. The TFT-LCD MDL panel is adapted for a low reflection and higher color type.

Features:

• LVDS interface with 1 pixel / clock
• High-speed response
• Low color shift image quality
• 6-bit +FRC color depth, display 16.7M colors
• Wide viewing angle
• DE (Data Enable) only mode
• ADS technology is applied for high display quality
• RoHS compliant

Specifications:

Absolute Maximum Ratings:

The followings are maximum values which, if exceed, may cause faulty operation or damage to the unit. The operational and non-operational maximum voltage and current values are listed in Table.

Note 1 : Wet bulb temperature should be 39℃ max. and no condensation of water.

Electrical Specifications:

Note 1 : The supply voltage is measured and specified at the interface connector of LCM.The current draw and power consumption specified is for VDD=3.3V,Test Pattern of power supply current.

Note 2 : The duration of rush current is about 2ms and rising time of Power Input is 1ms(min).

Note 3 :Calculated value for reference (Input pins*VPIN × IPIN) excluding inverter loss.

Backlight Electrical Specifications:

LED bar consists of 48LED packages,4 strings(parallel)*12packages(serial)

Note1: There are one light bar ,and the specified current is input LED chip 100% duty current

Note2: The sense current of each input pin is 55mA

Note3: PBL=4 Input pins*VPIN × IPIN

Note4: The lifetime is determined as the time at which luminance of LED become 50% of the initial brightness or not normal lighting at IPIN=55mA on condition of continuous operating at 25 ± 2℃

Interface Connection:

Optical Specification:

Note :

1. Viewing angle is the angle at which the contrast ratio is greater than 10. The viewing are determined for the horizontal or 3, 9 o‟clock direction and the vertical or 6, 12 o‟clock direction with respect to the optical axis which is normal to the LCD surface.

2. The White luminance uniformity on LCD surface is then expressed as : ΔY =Minimum Luminance of 9 points / Maximum Luminance of 9 points.(see Figure 1 shown in Appendix).

3. Contrast measurements shall be made at viewing angle of 9= 0.and at the center of the LCD surface. Luminance shall be measured with all pixels in the view field set first to white, then to the dark (black) state. (See Figure 2 shown in Appendix) Luminance Contrast Ratio (CR) is defined mathematically.

4. The color chromaticity coordinates specified in Table 9.shall be calculated from the spectral data measured with all pixels first in red, green, blue and white. Measurements shall be made at the center of the panel. The BLU is used by BOE.

5. Response time Tg is the average time required for display transition by switching the input signal as below table and is based on Frame rate fV =60Hz to optimize.

Operating Precautions:

1.Do not connector or disconnect the cable to/from the Module at the “Power On” Condition.

2.When the module is operating, do not lose CLK, ENAB signals. If any one of these signals is lost, the module would be damaged.

Shenzhen FRIDA LCD Co., Ltd is a high-tech enterprise specializing in LCD display and touch panel, smart cloud, software, hardware and mold development, is committed to becoming a standard and customized audio and video solution provider in AIOT field for our customers.
FRIDA LCD was founded in 2011, has experiences of 10 years in production and 3 years in solution development, and established a set of scientific, strict quality management system as the lifeline of the enterprise.Products from 0.96-32 inch LCD and touch panel.